![]()
An excellent initiative that gives this VFD even more value for money. Quote from: ToPNoTCH on March 19, 2010, 11:49:59 AM First off all thanks for the effort of making this plugin. I imagine this won't be an extreme alteration in code, but it would make the plugin compatible with the vast majority (if not all) types of RS485 interfaces/converters.īeside that the ADDC devices are much more expensive, so those who need to buy an adapter would find this an great modification i be live.Īgain thanks for your effort, it's greatly appreciated. #HUANYANG VFD PLUGIN FOR MACH3 UPDATE#I suggest that you update the plugin so that it raises RTS while sending and lower it directly when done. is the dynamic link library to pair with mach3 called the Huanyang VFD Mach3 PlugIn. Other adapters can only send data, which matches well with the behaviour i get (cant see PD001,PD002 but start spindle once, get estop directly afterwards). Set up Mach3 on PC to control VFD: Mach3, Config, Ports and Pins. It seems that your plugin raise the RTS all the time when its loaded thus making it only compatible with RS485 adapters that incorporates ADDC. Some RS485 adapters (mostly USB to RS485) incorporate "Automatic Data Direction Controll" (ADDC), which handle the above behaviour by it's hardware. ![]() One "normal" way to handle this with an RS232 converter, is to use the RTS pin to set the transceiver into Transmit mode, and directly afterwards the transmit lower it to This means that in someway the transceiver chip on the RS485 adapter need to be set in Transmit or Receive mode.Īs i understand it it is up to the implementation to handle this (RS485 don't care as it's an interface standard and not a protocol standard). The RS-485 standard which is used in this case states the communication allways is done using half-duplex on twowire. Hello Everyone, If you were using a Hunayang plugin for Mach3 to control VFD/spinde or using Spindle Talker than this macros for you. I'm sad to report that it did NOT work for me and i believe i know why. NEVER WORK ON A LIVE CIRCUIT.First off all thanks for the effort of making this plugin. ![]() It allows Mach3 to control the operation of the VFD via RS485 communication port. Best practice is to physically unplug any electrical device from the wall when doing any electrical work. This plugin has been written for use with the Huanyang series of Variable Frequency Drives (VFD). Im attempting to set the spindle to run through Mach3. Never make any connections or disconnections when any device is energised. #HUANYANG VFD PLUGIN FOR MACH3 MANUAL#Critical parameters and the recommended settings are outlined in this guide, however again please also do your own research and read the manual thoroughly. ![]() #HUANYANG VFD PLUGIN FOR MACH3 INSTALL#When in doubt, get a suitably qualified person to install and program. VFDs are complicated electronic devices and will be damaged or dangerous if not wired and configured correct. Wiring sample of the C25XP board connection with Huanyang VFD. Thoroughly read through the manual provided with the VFD and understand the function of the parameters before running the spindle. ![]() I set the parameters for VFD and plugin according to the instructions from the plugin (attached pictures). Mach3 is now configured properly for spindle relay and speed control. Spindles damaged by an incorrectly programmed VFD may void your warrantyĭISCLAIMER: Mains connections are to be done by a licensed electrician or suitably qualified person, always ask for a COES. I purchase a Huanyang Vfd and 18000RPM spindle kit on ebay. VFD Manual : GeneraI VFD setup: Héres the correct séttings for the Huányang VFD that aIways seems to comé with thése kits.F0NT. #HUANYANG VFD PLUGIN FOR MACH3 REGISTRATION#Please do not attempt to run the Spindle without first adjusting the VFD parameters or you may irreversibly damage the spindle. Huanyang Vfd Registration Process Or Registration is fast, simple and absolutely free, join the community today If you have any problems with the registration process or your account login, please contact us. /rebates/&252fhuanyang-vfd-plugin-for-mach3. Note: Any Mains power connections must be installed by a Licensed electrician or suitability qualified person. FAILURE TO DO SO WILL VOID ANY AND ALL WARRANTIES.īefore starting please read through all the instructions. #HUANYANG VFD PLUGIN FOR MACH3 DRIVERS#The author of this document is not liable or responsible for any accidents, injuries, equipment damage, property damage, loss of money or loss of time resulting from improper use of electrical or mechanical or software products.Īssembling electrical and mechanical CNC machine components like power supplies, motors, drivers or other electrical and mechanical components involves dealing with high voltage AC (alternating current) or DC (direct current) and other hazardous items which can be extremely dangerous and needs high attention to detail, experience, knowledge of software, electricity, electro-mechanics and mechanics.īEFORE MAKING ANY CONNECTIONS OR DISCONNECTIONS POWER MUST BE REMOVED FROM THE DEVICE AND THE CONTROLLER. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |